<form id="fprtl"><form id="fprtl"><th id="fprtl"></th></form></form>

            <address id="fprtl"><nobr id="fprtl"><nobr id="fprtl"></nobr></nobr></address>

                <form id="fprtl"></form><form id="fprtl"><form id="fprtl"><th id="fprtl"></th></form></form>

                  <address id="fprtl"></address>
                  

                            <address id="fprtl"><form id="fprtl"><track id="fprtl"></track></form></address>
                            <form id="fprtl"></form>

                              <form id="fprtl"></form>

                                  <form id="fprtl"></form>
                                  您好,歡迎來到濟南通宇恒成自動化工程有限公司網站!

                                  服務熱線

                                  當前位置: 首頁- 新聞中心 > 公司動態
                                  常見問題
                                  新聞中心

                                  仿威圖控制柜校線的標準是什么?

                                  發布時間:2024-03-05 來源:http://www.huexposure.com/ 瀏覽量:

                                  1、關閉電源:在進行校線之前,需要先關閉控制柜的電源,并確保所有的電氣元件都已經停止工作,以免造成事故。

                                  1. Turn off power: Before conducting calibration, it is necessary to turn off the power supply of the control cabinet and ensure that all electrical components have stopped working to avoid safety accidents.

                                  2、確定測量對象:根據需要,選定需要測量的電氣元件和信號線路,例如電機、接觸器、繼電器等。

                                  2. Determine the measurement object: Select the electrical components and signal circuits that need to be measured, such as motors, contactors, relays, etc., as needed.

                                  3、連接萬用表:將萬用表的測量頭與需要測量的電氣元件和信號線路相連接,通常需要使用插頭或者夾子等連接器,確保連接牢固。

                                  3. Connecting a multimeter: Connect the measuring head of the multimeter to the electrical components and signal lines that need to be measured, usually using connectors such as plugs or clips to ensure a secure connection.

                                  20210426030209150.jpg

                                  4、測量電壓:打開電源,啟動控制柜,測量相應電氣元件和信號線路的電壓值,根據測量值進行調整。

                                  4. Measure voltage: Turn on the power, start the control cabinet, measure the voltage values of the corresponding electrical components and signal lines, and adjust according to the measured values.

                                  5、校正電阻值:如果需要校正電氣元件的電阻值,可以使用萬用表進行測量,并根據測量值進行調整。

                                  5. Correction of resistance value: If it is necessary to correct the resistance value of electrical components, a multimeter can be used for measurement and adjustments can be made based on the measurement value.

                                  6、完成校線:根據需要進行多次測量和調整,直到達到預期的校線效果為止。

                                  6. Complete calibration: Conduct multiple measurements and adjustments as needed until the expected calibration effect is achieved.

                                  本文由山東仿威圖機柜提供技術支持,更多的詳細精彩內容請點擊我們的網站 http://www.huexposure.com ,我們將會全心全意為您提供滿意的服務。

                                  This article is supported by Shandong Fangweitu Cabinet. For more detailed and exciting content, please click on our website http://www.huexposure.com We will wholeheartedly provide you with satisfactory service.

                                  首頁首頁 產品產品 電話電話 置頂置頂
                                  伊人久久无码av一区二区三区&精品午夜在线一区二区三区&日本一区二区高清道免费&国产精品中文字幕在线

                                        <form id="fprtl"><form id="fprtl"><th id="fprtl"></th></form></form>

                                            <address id="fprtl"><nobr id="fprtl"><nobr id="fprtl"></nobr></nobr></address>

                                                <form id="fprtl"></form><form id="fprtl"><form id="fprtl"><th id="fprtl"></th></form></form>

                                                  <address id="fprtl"></address>
                                                  

                                                            <address id="fprtl"><form id="fprtl"><track id="fprtl"></track></form></address>
                                                            <form id="fprtl"></form>

                                                              <form id="fprtl"></form>

                                                                  <form id="fprtl"></form>